Phoenix Quality Drywall serves commercial properties across Phoenix with drywall installation, repair, finishing, and texture matching. Our scope includes ceiling drywall repair, drywall hole repair, water damage drywall repair, plaster repair, and metal stud framing. We work in offices near the Camelback Corridor, warehouses along the I-17 and I-10 industrial corridors, and retail build-outs from Deer Valley to South Phoenix. Each project receives the same attention to framing, board installation, and finish quality regardless of square footage.
Commercial walls must account for fire ratings, sound control, moisture exposure, heavy traffic, and Phoenix heat before the first sheet is hung. Our crews install Type X and Type C gypsum board to ASTM C1396 and C840 specifications, frame with 20-gauge or 25-gauge metal studs according to load requirements, and apply level 4 or level 5 finishes based on exposure and lighting. We are a licensed Arizona contractor and carry general liability coverage on every project. A site walk lets us confirm the assembly, coordinate rough-ins, and quote the work before construction begins.
In a metro area with more than 5.19 million residents, offices, warehouses, and tenant improvements need drywall scopes that stay coordinated from layout through final primer. Request a commercial drywall estimate for a ground-up build-out, retrofit, or targeted repair.
Phoenix Quality Drywall provides commercial drywall service throughout Phoenix, Tempe, Scottsdale, Mesa, Glendale, and Chandler.
Commercial drywall is gypsum board made for the fire-resistance, impact-resistance, and sound-control demands of offices, retail centers, warehouses, and other high-traffic interiors. Its gypsum core may be reinforced with glass fibers and additives based on the performance an assembly must provide.
Commercial specifications commonly call for 5/8-inch board instead of the 1/2-inch board often used in residential work. The added thickness can improve impact durability, fire performance, and STC ratings for shared walls.
Type C board is used in stairwells, corridors, and shared-tenant walls when the specified assembly requires one-hour or two-hour fire resistance. Phoenix enforces the International Building Code with local amendments through its Planning and Development Department, so the installed assembly must match the rating shown in the plans.
A commercial drywall scope can combine the board type, framing, finish, moisture protection, and acoustic performance each part of a building requires.
Our commercial work covers new interiors, tenant improvements, targeted repairs, and finish restoration. Each service is planned around the existing structure, specified assembly, trade rough-ins, and final appearance.
We install gypsum board for office build-outs, warehouse retrofits, retail interiors, and other commercial partitions. Sheets are hung horizontally where practical to reduce joint count, staggered, and fastened on the schedule required by the assembly.
Request Estimate
We set metal track and studs to line and plumb, using 20-gauge or 25-gauge members on 16-inch or 24-inch centers according to wall height and load. Steel framing resists the moisture swings and thermal movement associated with Phoenix summers above 100 degrees.
Request Estimate
Joints are taped with paper or mesh, built out with three coats of joint compound, and sanded between coats. Corner bead receives the same careful treatment so edges stay straight and the finished surface reads cleanly under office lighting.
Request Estimate
We match smooth, orange peel, knockdown, and hand-troweled finishes by preparing test boards on-site before applying texture to the repaired wall. Popcorn texture removal and spray texture work are blended to the existing pattern rather than treated as a one-texture-fits-all job.
Request Estimate
Our repair scope covers holes from equipment moves or forklift impacts, water-damaged sections, cracked plaster, and worn commercial surfaces. Damaged board is cut back to sound material, backed or reframed as needed, and rebuilt to match the existing thickness, fire rating, texture, and finish. Same-day drywall service is available when a hole must be patched before an inspection.
Request Estimate
We repair drywall ceilings affected by HVAC condensation, roof leaks, settling, and mechanical work, including tie-ins around suspended grid systems. When structural framing is involved, engineered blocking is installed before the ceiling is closed and finished.
Request EstimateBoard, framing, finish, and specialty details should follow the room's occupancy, exposure, sound requirements, and design. These commercial options address the conditions most often found in Phoenix offices, warehouses, retail spaces, restrooms, and shared-tenant interiors.
Fire-rated walls are built as complete tested assemblies, not by board type alone. We match the board, framing, fastener schedule, joints, and penetrations to the rating specified for the occupancy and egress path.
Moisture-resistant board gives wet-prone commercial spaces a better starting point when plumbing leaks or condensation occur. The selected product still has to match the wall's thickness and any required fire rating.
Soundproof drywall installation helps separate conversations and everyday activity between commercial rooms and tenant spaces. The framing, board thickness, joints, and penetrations all influence the finished partition's sound performance.
Finish selection depends on how visible the surface will be, the planned coating, and the lighting that crosses it. A final sand, PVA primer, and inspection under raking light reveal shadowing before paint makes flaws permanent.
Commercial ceiling details often require dedicated framing before drywall is installed. We build and finish these assemblies so transitions align, repairs blend under lighting, and the completed feature holds its shape.
The right approach begins with the plans, occupancy, wall height, load, fire rating, moisture exposure, sound goals, and final lighting. Reviewing those factors together helps prevent rework after framing, board, or finish work is already complete.
We review the plans and confirm fire-rating requirements with the general contractor or property manager before framing begins. Board type, fastening, penetrations, and assembly documentation stay tied to the specified rating.
Layout is checked against architectural drawings, door and window openings, and plumbing and electrical rough-ins. Blocking for wall-mounted fixtures and coordination with mechanical trades happen before board closes the wall.
We select the finish level and texture for the wall's exposure, coating, and lighting instead of applying the same detail everywhere. Test-board matching, careful corner bead, final sanding, primer, and a raking-light walk-through help the work disappear into the finished interior.
Phoenix Quality Drywall is a licensed Arizona contractor with general liability coverage on every project. We coordinate demolition and disposal, framing, hanging, finishing, and inspection documentation as one scope, and our estimate breaks out material, labor, and finish level before work begins.
Request EstimateThe correct board can still fail the intended rating when framing, joints, fasteners, or penetrations do not match the tested assembly. We rebuild affected areas to the specified detail and keep the assembly information ready for inspection.
Discoloration, sagging, musty odors, and soft spots can signal moisture behind the surface. Monsoon roof leaks and flash flooding in July and August make early removal important, because affected board left in place can become a mold problem.
Rushed taping, uneven compound, or poorly set corner bead can show as ridges and shadows under office lighting. Reworking the joint profile and checking it under raking light addresses the surface before final paint.
A patch remains obvious when its spray pattern, knockdown timing, or hand-troweled movement differs from the surrounding wall. We use on-site test boards to tune the texture before applying it to the repaired surface.
Equipment moves, forklift bumps, fixtures, and daily traffic can leave anything from a small puncture to a panel-wide break. The repair method is selected by size, with larger openings cut back to studs and rebuilt with backing and a full board patch.
HVAC condensation, roof leaks, settling, and unsupported mechanical loads can crack or deform ceiling drywall. Structural blocking is addressed before patching so a ceiling does not sag again six months later.
The same coordinated sequence applies to a 2,000-square-foot office suite and a full warehouse fit-out. We move from site review and layout through framing, board, finish, primer, and a final quality check.
We walk the space, review architectural plans, confirm occupancy and fire-rating requirements, and identify ceiling height, access, moisture, sound, and finish conditions. The estimate then separates material, labor, and finish level.
Wall lines, door openings, windows, plumbing, and electrical rough-ins are marked before track and studs are set. The framing crew selects the required gauge and spacing, then checks every wall for line and plumb.
Blocking is installed for wall-mounted fixtures, and electrical and mechanical work is coordinated before the cavities are covered. Openings and penetrations are checked so the board crew is not reworking completed walls.
Sheets are oriented to reduce joints where possible, staggered, cut closely around outlets and HVAC penetrations, and screwed at the spacing required by the assembly. Fire-rated walls follow their exact board and fastening schedule.
Joints and corner bead are taped, coated, and sanded to the chosen finish level. If texture is required, a test board is used to match the existing smooth, orange peel, knockdown, hand-troweled, or spray pattern.
The finished surface receives a final sand and PVA primer before it is checked under raking light. We review joints, corners, texture transitions, and repaired areas before paint goes on.
Tell us whether you are planning a tenant improvement, new partition layout, fire-rated assembly, ceiling repair, or targeted patch. We will walk the site, review the required scope, and prepare an estimate based on materials, labor, access, and finish level.
These answers cover board types, thickness, Phoenix code context, permits, framing, finishing, and common commercial drywall cost factors.
Call Our Drywall TeamType C drywall is commonly specified for stairwells, corridors, and shared-tenant walls with strict fire-code requirements. Type X is also used in one-hour and two-hour fire-resistant assemblies. The correct board depends on the tested assembly and the occupancy classification shown in the plans.
Commercial drywall is gypsum board used to build interior walls and ceilings in offices, retail spaces, warehouses, and other commercial buildings. Its core, thickness, and assembly details are selected for fire resistance, impact resistance, sound control, or moisture exposure.
Phoenix commercial specifications most commonly use 5/8-inch drywall, especially for Type X and Type C assemblies in corridors, stairwells, and demising walls. Some non-rated interior partitions use 1/2-inch board, but the plans and required assembly determine the final thickness.
Phoenix enforces the International Building Code with local amendments through the Planning and Development Department. Commercial drywall assemblies must provide the fire rating required for the building's occupancy and egress conditions, so we follow the assembly identified by the architect or plan review.
In most Phoenix jurisdictions, bathroom work involving structural changes, plumbing relocation, or electrical work requires a permit, while cosmetic drywall repair alone typically does not. Commercial tenant improvements almost always require permits through the Planning and Development Department. We review the planned scope during the site walk so permitting can be addressed before work begins.
Arizona homes most commonly use 1/2-inch board on walls and either 1/2-inch or 5/8-inch board on ceilings, depending on framing and fire-separation needs. Garages and shared walls between attached homes often require 5/8-inch Type X board. Commercial buildings use 5/8-inch board more often because code and assembly performance drive the specification.
Commercial drywall installation in the Phoenix metro runs roughly $1.50 to $3.50 per square foot depending on board type, ceiling height, and finish level. A site walk and plan review are needed to price the actual framing, access, assembly, and finish requirements.
Phoenix metro tenant-improvement labor runs roughly $55 to $75 an hour for hanging crews and $60 to $80 an hour for tapers and finishers. The project quote also accounts for material, wall height, access, framing, board type, and finish level.
Water damage drywall repairs typically range from $350 to $2,000-plus depending on how far moisture traveled behind the wall. The affected area is cut back to dry, sound material, the framing is treated if needed, and new board is matched to the existing thickness and fire rating.
A small drywall hole under two inches usually receives a self-adhesive mesh patch and two coats of joint compound, with texture matched and primer applied; this work runs about $200 to $350 in many Phoenix settings. Medium to large repairs are cut back to studs, backed, patched with board, and taped on all four sides, with typical costs of $350 to $650 before added framing or fire-rated assembly work.
Commercial walls may use 20-gauge or 25-gauge metal studs on 16-inch or 24-inch centers depending on wall height and load. The plans and specified assembly determine the final gauge, spacing, blocking, and track details.
Level 4 is used for many standard commercial surfaces, while level 5 is selected where exposure, coating, or lighting makes surface uniformity more demanding. We choose the finish level from the wall's final conditions and inspect the surface under raking light before paint.
We prepare test boards on-site to compare the spray pattern, knockdown, smooth finish, or hand-troweled texture before touching the repaired wall. Once the pattern matches, the repair is textured, primed, and checked under normal and raking light so the patch blends with the surrounding surface.